The Kidde KN-COSM-IBACA uses breakthrough technology to offer a fast response to real fires, including smoldering and fast-flaming, as well as protect you from carbon monoxide and dramatically reduce the chance of nuisance alarms. The Intelligent sensor technology combines the detection capabilities of an ionization smoke sensor – which is more likely to detect smaller, less visible fire particles, like those produced by flaming fires – with that of an electrochemical sensor, which is used to detect CO. Since carbon monoxide is present in all fires, having both detection chambers work together in one alarm is a breakthrough in the fire safety industry. When either sensor notices a potential hazard, it will communicate with the other. Depending on what is detected, the alarm will adjust its smoke sensitivity in order to better discriminate between a real hazard and a false one. This constant communication enhances the alarm’s overall performance in all fires, and significantly reduces the potential for a nuisance alarm. Ionization or Photoelectric Alarms? Leading authorities recommend that both ionization and photoelectric smoke alarms be installed to help insure maximum detection of the various types of fires that can occur within the home. Ionization sensing alarms may detect invisible fire particles (associated with fast flaming fires) sooner than photoelectric alarms. Photoelectric sensing alarms may detect visible fire particles (associated with slow smoldering fires) sooner than ionization alarms.
A single unit can be installed where previously, two were needed. Reduces installation time and protects against both fire and carbon monoxide dangers.
Combines the detection capabilities of an ionization smoke sensor with that of an electrochemical carbon monoxide sensor. When either sensor notices a potential hazard, the alarm will adjust its smoke sensitiivity to differentiate between a real hazard and a false one.
Announces the hazard type detected (in English and French). Alarm announces “FIRE!” when a smoke or fire hazard is detected and announces “WARNING! CARBON MONOXIDE!” when a CO hazard is detected. Also announces “LOW BATTERY” when it is time to replace the batteries.
Will interconnect with up to 24 other devices (18 of which can be initiating), including smoke alarms (limit of 12), CO and heat alarms.
Change batteries without the need to remove the unit from the ceiling, providing continuous protection in the case of a power outage.
Unit will lock to mounting bracket to deter theft or tampering.
Ten (10) years after unit is first powered, this alarm will beep two times every 30 seconds to indicate it is time to replace the alarm.
The green LED will flash every second during alarm. When the alarm condition goes away, the originating alarm unit will flash the green LED every 16 seconds until the Test/ Reset button is pressed, thus resetting the alarm.
Tests the alarm circuitry and triggers the voice announcement.
Temporarily silences nuisance alarms for approximately 9 minutes (will announce “HUSH MODE ACTIVATED,” or “HUSH MODE CANCELLED.”).
Resets the carbon monoxide alarm
If alarm has detected a CO level of 100ppm or higher since it was last reset, the voice alarm will announce “CAUTION, CARBON MONOXIDE PREVIOUSLY DETECTED”
The red LED will flash and be accompanied by three long alarm beeps followed by a verbal warning message “FIRE!”. The alarm pattern will repeat until smoke is eliminated.
Four short alarm beeps followed by a verbal warning “WARNING! CARBON MONOXIDE!” This continues until the unit is reset or the CO is eliminated.
One chirp followed by warning “LOW BATTERY.” The red LED light will flash. This pattern will continue every minute for at least seven days. Under battery power, the “LOW BATTERY” voice only occurs once every 15 minutes.
“HUSH MODE ACTIVATED” and “HUSH MODE CANCELLED” voice announcement.
|120 V AC, 60Hz 45mA max per alarm 2 AA battery backup
|Smoke: Ionization, CO: Electrochemical
|85dB at 10ft
|4.4˚C (40˚F) to 37.8˚C (100˚F)
|10%-95% relative humidity, non-condensing
|12.3cm in diameter x 3.2cm depth
|Quick connect plug with 15.2 cm (6”) pigtails
|Up to 24 Kidde devices (of which 18 can be initiating)
The combination alarm should be installed to comply with all local codes having jurisdiction in your area. Make certain all alarms are wired to a single, continuous (non-switched) power line, which is not protected by a ground fault interrupter. A maximum of 305m (1000’) of wire can be used in the interconnect system. Use standard CSA listed household wire (18 gauge or larger as required by local codes).
Is your home or office equipped with Smoke & Carbon Monoxide alarms to properly protect you, your family, and your staff? Learn more about Kidde's fire alarm:
“Look. Listen. Learn. Be aware. Fire can happen anywhere™”, this year's fire prevention theme.
Learning the basics of fire safety is the first step in fighting fire – and it just so happens to be the most important.